| 泡罩包装的工艺 |
| 添加时间：2018/1/15 16:18:24 浏览次数： |
| 泡罩包装工艺 Packing process of bubble cover 泡罩包装的泡罩空穴有大有小，形状因被包装物品的形状而异；有用衬底的，也有不用衬底的。而且泡罩包装机的类型比较多。尽管如此,泡罩包装的基本原理大致上是相同的。其典型工艺过程为： The bubbles in the bubble wrap are large and small, and the shape varies from the shape of the packaged goods; the substrate is used and the substrate is not used. And the type of blister packaging machine is more. In spite of this, the basic principles of the bubble wrap are roughly the same. The typical process is as follows: 片材加热→薄膜成型→充填产品→安放衬底→热封→切边修整 Sheet heating, film forming, filling product, placement substrate, hot sealing, trimming and trimming 完成泡罩包装工艺过程可用手工操作、半自动操作和自动操作3种方式。 The process of packing the bubble cover can be done in 3 ways: manual operation, semi automatic operation and automatic operation. （1）手工操作 (1) manual operation 塑料薄片泡罩预先成型,衬底预先印刷并切割好;包装时用手工将产品装入泡罩内,盖上衬底,然后用热封器将泡罩与衬底封合在一体。有些产品对流通环境的温度和湿度要求不高,可不予热封,而用订书机订封。 The plastic thin blister is pre molded, and the substrate is pre printed and cut. When packaging, the product is loaded into the bubble cap by hand, and the substrate is covered. Then the heat seal is applied to seal the blister and the substrate together. Some products require not high temperature and humidity in the circulation environment. They can not be sealed and sealed with a stapler. （2）半自动化操作 (2) semi automatic operation 将卷筒的或单张的塑料薄片送入半自动泡罩包装机内,机器操作是连续的或间歇的;成型模具的数量根据产品的大小和生产量而定,一般都采用多列式;薄片经成型冷却后,用手工将产品装入泡罩内;将卷筒或单张形式的印刷好的衬底覆盖在泡罩上,再进行热封、切边,得到完整的包装件。 The plastic sheet reel or leaflets into semi automatic blister packaging machine, the machine operation is continuous or intermittent; the number of mold is determined according to the size and quantity of the products, generally using one sheet; forming after cooling, use the manual product into the blister in the substrate drum; or in a single form of printed coverage in a bubble, then the heat sealing and cutting edge, get the complete package. （3）自动化操作 (3) automatic operation 自动化操作时,除了以上包装工序外,还可将打印、装说明书、装盒等工序与生产线相连,其生产流程见下图。 In automatic operation, in addition to the above packaging process, printing, packing, packing and other processes can be connected to the production line. The production process is shown below. 图中a表示卷筒塑料薄片向前输送;b表示薄片加热软化,在模具内用压缩空气压制或用抽真空吸制成泡罩;c表示用自动上料机构充填产品;d表示检测泡罩成型质量和充填是否合格,在快速自动生产线上,常采用光电探测器,发现不合格产品时,将废品信号送至记忆装置,待切边工序完成后将废品自动剔除;e表示卷筒衬底材料覆盖在已充填好泡罩上;f表示用板式或辊式热封器将泡罩与衬底封合在一起;g表示在衬底背面打印号码和日期等;h表示切边后形成包装件。如果装有剔除废品装置,则在切边工序之后,根据记忆装置储存的信号剔除废品。 Figure a said plastic sheet conveying roll forward; B sheet heating softening, with compressed air or by pressing vacuum suction blister made in the mold; C automatic feeding mechanism for filling products; D detection of blister forming quality and filling is qualified in the rapid automatic production line, often using photoelectric detector, found substandard products, will reject the signal sent to the memory device, the trimming process after the completion of the automatic elimination of waste; e said drum substrate material covered in has been filling the blister; F is represented by the plate or roller type heat sealing device of the blister and sealing the substrate together; G said in substrate backprinting number and date; h said cutting edge after forming packing. If the scrap device is removed, the scrap is removed after the cutting process, according to the signal stored in the memory device. 这种自动包装生产线适合于单一品种大批量生产,它的优点是生产率高、成本低,而且符合卫生要求。 This automatic packaging line is suitable for a single variety of mass production, its advantages are high productivity, low cost, and meet the health requirements. |
| 上一页 铝塑泡罩包装机应用中的常见问题 |
| 下一页 泡罩包装机工作原理及工艺流程 |
Copyright © 技术支持：遨游网络